3D printer, resin (Anycubic Photon 5.5) ID:159 - Revision history

Parker.link: Fix headings

2023-02-23T04:39:23Z

Fix headings

← Older revision		Revision as of 04:39, 23 February 2023
Line 16:		Line 16:
	This printer is an Anycubic Photon 5.5. Note that it has undergone an upgrade, making it more similar to the ELEGOO MARS 2 PRO (useful for slicing).		This printer is an Anycubic Photon 5.5. Note that it has undergone an upgrade, making it more similar to the ELEGOO MARS 2 PRO (useful for slicing).

			== Specs ==
	Resolution/Build Size:		Resolution/Build Size:

Line 22:		Line 23:
	*Z: 160mm		*Z: 160mm

	==~~Manuals~~==		==Documentation==

	[https://www.anycubic.com/products/anycubic-photon-3d-printer Product Page]		[https://www.anycubic.com/products/anycubic-photon-3d-printer Product Page]
Line 28:		Line 29:
	[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]		[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]

	==~~Your First Print~~==		==Usage==
	No training is required for this printer. Get someone to walk you through the process, and then you can print using it.		No training is required for this printer. Get someone to walk you through the process, and then you can print using it.

Line 52:		Line 53:
	#Start the print.		#Start the print.
	#Listen to ensure that 30 seconds after the print starts, you hear a popping noise as the print separates from the clear plastic sheet and stays attached to the blue build plate. Cancel the print if you don't hear the popping noise, probably.		#Listen to ensure that 30 seconds after the print starts, you hear a popping noise as the print separates from the clear plastic sheet and stays attached to the blue build plate. Cancel the print if you don't hear the popping noise, probably.
	#You can estimate the print time based on the Duration and Percent Complete.		#You can estimate the print time based on the Duration and Percent Complete.
	#When complete, use the [[Curing station (Anycubic Wash and Cure Machine) ID:160\|Curing station]] guide/video to post-process, clean, and cure your print.		#When complete, use the [[Curing station (Anycubic Wash and Cure Machine) ID:160\|Curing station]] guide/video to post-process, clean, and cure your print.
	#Drain the excess resin in the tray back into the bottle. Avoid contamination. Use a squeegee, and don't break the clear plastic sheet.		#Drain the excess resin in the tray back into the bottle. Avoid contamination. Use a squeegee, and don't break the clear plastic sheet.

Parker.link: /* Your First Print */ Add end-of-print instructions

2023-02-23T04:26:23Z

Your First Print: Add end-of-print instructions

← Older revision		Revision as of 04:26, 23 February 2023
Line 52:		Line 52:
	#Start the print.		#Start the print.
	#Listen to ensure that 30 seconds after the print starts, you hear a popping noise as the print separates from the clear plastic sheet and stays attached to the blue build plate. Cancel the print if you don't hear the popping noise, probably.		#Listen to ensure that 30 seconds after the print starts, you hear a popping noise as the print separates from the clear plastic sheet and stays attached to the blue build plate. Cancel the print if you don't hear the popping noise, probably.
	#~~When~~ the print is complete, ~~you're all done.~~ (~~just kidding~~, the ~~messy~~ resin ~~part starts now)~~		#You can estimate the print time based on the Duration and Percent Complete.
			#When complete, use the [[Curing station (Anycubic Wash and Cure Machine) ID:160\|Curing station]] guide/video to post-process, clean, and cure your print.
			#Drain the excess resin in the tray back into the bottle. Avoid contamination. Use a squeegee, and don't break the clear plastic sheet.
			#Wipe down with IPA.

	==Discussion Threads==		==Discussion Threads==

	[https://forum.protospace.ca/t/resin-printers-down/688 Resin Printers Down]		[https://forum.protospace.ca/t/resin-printers-down/688 Resin Printers Down]

Parker.link: /* Your First Print */ Add gloves to procedure

2023-02-23T04:19:39Z

Your First Print: Add gloves to procedure

← Older revision		Revision as of 04:19, 23 February 2023
Line 18:		Line 18:
	Resolution/Build Size:		Resolution/Build Size:

	* X: 1620px (82.62mm)		*X: 1620px (82.62mm)
	* Y: 2560px (130.56mm)		*Y: 2560px (130.56mm)
	* Z: 160mm		*Z: 160mm

	==Manuals==		==Manuals==
Line 43:		Line 43:
	##Add supports as required.		##Add supports as required.
	##Save to a USB stick.		##Save to a USB stick.
			#Don gloves. The resin washes off pretty well with soap, but you'll wanna wear gloves.
	#Clean the clear plate/resivoir that goes atop the LCD using IPA. Be careful not to puncture it with your paper towel (??).		#Clean the clear plate/resivoir that goes atop the LCD using IPA. Be careful not to puncture it with your paper towel (??).
	#Install the clear plate on the printer and tighten the screws.		#Install the clear plate on the printer and tighten the screws.

Parker.link: Add intro

2023-02-23T03:57:14Z

Add intro

← Older revision		Revision as of 03:57, 23 February 2023
Line 12:		Line 12:
	\| caption = Anycubic Photon 5.5 Resin Printer		\| caption = Anycubic Photon 5.5 Resin Printer
	\| id = 159		\| id = 159
	}}		}}This resin printer is the smaller of two resin printers at Protospace. Resin printers are ideal for 3D printing very fine details, but take a bit of extra effort (compared to their FDM counterparts).

			This printer is an Anycubic Photon 5.5. Note that it has undergone an upgrade, making it more similar to the ELEGOO MARS 2 PRO (useful for slicing).

			Resolution/Build Size:

			* X: 1620px (82.62mm)
			* Y: 2560px (130.56mm)
			* Z: 160mm

	==Manuals==		==Manuals==
Line 20:		Line 28:
	[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]		[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]

	== Your First Print ==		==Your First Print==
	No training is required for this printer. Get someone to walk you through the process, and then you can print using it.		No training is required for this printer. Get someone to walk you through the process, and then you can print using it.

	Included here is a step-by-step guide of how to use this 3D printer well.		Included here is a step-by-step guide of how to use this 3D printer well.

	# Turn on the power bar above the printer. Ensure the heated enclosure also turns on and is set to 25C-30C.		#Turn on the power bar above the printer. Ensure the heated enclosure also turns on and is set to 25C-30C.
	# Slice your file on the computer using the Chitubox program.		#Slice your file on the computer using the Chitubox program.
	## Go to "Settings" on the right side.		##Go to "Settings" on the right side.
	## Select the "Chitusystems Mono Upgrade" machine on the far-left.		##Select the "Chitusystems Mono Upgrade" machine on the far-left.
	## Select the "... BASELINE ..." profile at the top.		##Select the "... BASELINE ..." profile at the top.
	## Duplicate the profile if you intend to make changes to it. Include your name and project name.		##Duplicate the profile if you intend to make changes to it. Include your name and project name.
	## Make changes to setting as desired. Large non-hollow objects may need more lowering time and curing time. Layer heights can be changed as well.		##Make changes to setting as desired. Large non-hollow objects may need more lowering time and curing time. Layer heights can be changed as well.
	## Avoid creating suction-cup inclusions by using the Remove Hole button to remove holes along the build plate of the model. You can also redesign your model, or rotate your model to avoid this phenomenon.		##Avoid creating suction-cup inclusions by using the Remove Hole button to remove holes along the build plate of the model. You can also redesign your model, or rotate your model to avoid this phenomenon.
	## Add supports as required.		##Add supports as required.
	## Save to a USB stick.		##Save to a USB stick.
	# Clean the clear plate/resivoir that goes atop the LCD using IPA. Be careful not to puncture it with your paper towel (??).		#Clean the clear plate/resivoir that goes atop the LCD using IPA. Be careful not to puncture it with your paper towel (??).
	# Install the clear plate on the printer and tighten the screws.		#Install the clear plate on the printer and tighten the screws.
	# Clean the build plate with IPA. Install it on the printer. Tighten the screw.		#Clean the build plate with IPA. Install it on the printer. Tighten the screw.
	# Optionally level the build plate (TODO write instructions for this).		#Optionally level the build plate (TODO write instructions for this).
	# Insert the USB stick into the right side of the printer.		#Insert the USB stick into the right side of the printer.
	# Use the screen to go to Print, and select your file. If you saved the file right, you should see a blue preview of your model.		#Use the screen to go to Print, and select your file. If you saved the file right, you should see a blue preview of your model.
	# Start the print.		#Start the print.
	# Listen to ensure that 30 seconds after the print starts, you hear a popping noise as the print separates from the clear plastic sheet and stays attached to the blue build plate. Cancel the print if you don't hear the popping noise, probably.		#Listen to ensure that 30 seconds after the print starts, you hear a popping noise as the print separates from the clear plastic sheet and stays attached to the blue build plate. Cancel the print if you don't hear the popping noise, probably.
	# When the print is complete, you're all done. (just kidding, the messy resin part starts now)		#When the print is complete, you're all done. (just kidding, the messy resin part starts now)

	==Discussion Threads==		==Discussion Threads==

	[https://forum.protospace.ca/t/resin-printers-down/688 Resin Printers Down]		[https://forum.protospace.ca/t/resin-printers-down/688 Resin Printers Down]

Parker.link: Add guide

2023-02-23T03:53:02Z

Add guide

@@ Line 19: / Line 19: @@
 [https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]
 ==Discussion Threads==
 [https://forum.protospace.ca/t/resin-printers-down/688 Resin Printers Down]

Kent.brockman at 00:23, 2 January 2022

2022-01-02T00:23:50Z

← Older revision		Revision as of 00:23, 2 January 2022
Line 19:		Line 19:

	[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]		[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]

			==Discussion Threads==

			[https://forum.protospace.ca/t/resin-printers-down/688 Resin Printers Down]

Kent.brockman: /* Manuals */

2022-01-02T00:20:55Z

Manuals

← Older revision		Revision as of 00:20, 2 January 2022
Line 17:		Line 17:

	[https://www.anycubic.com/products/anycubic-photon-3d-printer Product Page]		[https://www.anycubic.com/products/anycubic-photon-3d-printer Product Page]

	[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]		[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]

Kent.brockman at 00:20, 2 January 2022

2022-01-02T00:20:48Z

← Older revision		Revision as of 00:20, 2 January 2022
Line 13:		Line 13:
	\| id = 159		\| id = 159
	}}		}}

			==Manuals==

			[https://www.anycubic.com/products/anycubic-photon-3d-printer Product Page]
			[https://wiki.protospace.ca/images/6/60/NL-POT011-C_ANYCUBIC_Photon-english-20190906-V13.pdf Manual]

Kent.brockman: Created page with " {{Equipment page | toolname = Anycubic Photon 5.5 Resin Printer | model = Photon 5.5 | serial = 00340019-30384717-36333332-71 | owner =..."

2022-01-02T00:16:43Z

Created page with " {{Equipment page | toolname = Anycubic Photon 5.5 Resin Printer | model = Photon 5.5 | serial = 00340019-30384717-36333332-71 | owner =..."

New page

{{Equipment page
| toolname = Anycubic Photon 5.5 Resin Printer
| model = Photon 5.5
| serial = 00340019-30384717-36333332-71
| owner = ??
| loanstatus = ??
| arrived = ??
| location = 3D Printer Village
| status = Functional
| permission = ??
| certification = ??
| caption = Anycubic Photon 5.5 Resin Printer
| id = 159
}}