Vacuum cart ID:134 - Revision history

Cjs: updated location

2019-10-19T18:21:43Z

updated location

← Older revision		Revision as of 18:21, 19 October 2019
Line 1:		Line 1:
	{{Equipment page		{{Equipment page
	\| toolname = Vacuum ~~Cart~~		\| toolname = Vacuum cart
	\| model = DIY		\| model = DIY
	\| serial = N/A		\| serial = N/A
	\| owner = Janet M		\| owner = Janet M
	\| loanstatus = Semi-~~Permanent Loan~~		\| loanstatus = Semi-permanent loan
	\| arrived = 2014		\| arrived = Before 2014-10-29
	\| location = ~~Mobile, Woodshop~~		\| location = Laser cutter area
	\| status = Working		\| status = Working
	\| permission = Open to Members		\| permission = Open to Members
	\| certification = Demo ~~Required~~		\| certification = Demo required
	\| id = 134		\| id = 134
	}}		}}

	==Usage ~~Notes~~==		==Usage notes==

	* Uses vacuum pump to create powerful vacuum, slowly.		* Uses vacuum pump to create powerful vacuum, slowly.

Cjs: updated image link

2019-02-01T10:52:17Z

updated image link

← Older revision		Revision as of 10:52, 1 February 2019
Line 1:		Line 1:
	{{Equipment page		{{Equipment page
	\|toolname=Vacuum Cart		\| toolname = Vacuum Cart
	\|model=DIY		\| model = DIY
	\|serial=N/A		\| serial = N/A
	\|owner=Janet M		\| owner = Janet M
	\|loanstatus=Semi-Permanent Loan		\| loanstatus = Semi-Permanent Loan
	\|arrived=2014		\| arrived = 2014
	\|location=Mobile, Woodshop		\| location = Mobile, Woodshop
	\|status=Working		\| status = Working
	\|permission=Open to Members		\| permission = Open to Members
	\|certification=Demo Required		\| certification = Demo Required
	\|~~itemphoto~~=~~[[File:Vacuum_former_with_reservoir,_oven,_and_debris.jpg\|350px\|thumb\|right\|]]~~		\| id = 134
	}}		}}

	==Usage Notes==		==Usage Notes==

Cjs: Cjs moved page Vacuum cart to Vacuum cart ID:134: updated to follow naming conventions

2019-02-01T10:49:32Z

Cjs moved page Vacuum cart to Vacuum cart ID:134: updated to follow naming conventions

← Older revision	Revision as of 10:49, 1 February 2019
(No difference)

Cjs: Updated template names

2016-11-10T14:46:00Z

Updated template names

← Older revision		Revision as of 14:46, 10 November 2016
Line 1:		Line 1:
	{{~~Template:EquipmentPage~~		{{Equipment page
	\|toolname=Vacuum Cart		\|toolname=Vacuum Cart
	\|model=DIY		\|model=DIY

Matt: /* Usage Notes */

2016-03-31T04:13:08Z

Usage Notes

← Older revision		Revision as of 04:13, 31 March 2016
Line 21:		Line 21:
	* Plans for full size vacuum bed with infra-red bulb-based plastic heater above.		* Plans for full size vacuum bed with infra-red bulb-based plastic heater above.
	* Mates with 8' vacuum cannon accessory too.		* Mates with 8' vacuum cannon accessory too.
			* Doesn't like to run without resistance.
			* There should be a minimum 5:1 ratio of liquid you are degassing to chamber size (the amount you're degassing is no more than 1/5 the size of the chamber).
			* Try to avoid degassing anything that will boil under vacuum at 20 degrees Celsius (this includes water) as it will contaminate the oil in the vacuum pump. This is because we are not running a cold trap like a fancy laboratory.
			* Other than that its pretty much mechanically self explanatory, the two large tanks are there so you can pre vac them out and use them to pull the chamber down quickly if you have a fast setting resin.

	==Specs==		==Specs==

Matt: Seeded Page

2016-01-26T00:35:49Z

Seeded Page

New page

{{Template:EquipmentPage
|toolname=Vacuum Cart
|model=DIY
|serial=N/A
|owner=Janet M
|loanstatus=Semi-Permanent Loan
|arrived=2014
|location=Mobile, Woodshop
|status=Working
|permission=Open to Members
|certification=Demo Required
|itemphoto=[[File:Vacuum_former_with_reservoir,_oven,_and_debris.jpg|350px|thumb|right|]]
}}
==Usage Notes==

* Uses vacuum pump to create powerful vacuum, slowly.
* Stores vacuum, optionally, in two 14" diameter storage tanks, takes several minutes to charge.
* Cart contains vacuum degassing chamber, to remove bubbles from fast setting epoxies
* Ball valves allow vacuum to be dumped from the storage tanks into the degassing chamber instantly.
* Has small vacuformer (6 inch x 8 inch)
* Plans for full size vacuum bed with infra-red bulb-based plastic heater above.
* Mates with 8' vacuum cannon accessory too.

==Specs==